Create Config
X

G5 Ordering Information

PART NUMBER

DESCRIPTION

BOX/BAG
QTY

CARTON
QTY

G5-22

G5 Adhesive, 22 Fluid Oz. Cartridge

N/A

6

E55

Mixing
Nozzle diameter fits 3/8" to 5/8" holes
(overall length of nozzle 14")

24

N/A

E102

Hand Dispenser for G5-22 Cartridges —
Dispenses both18 ounce and 22 ounce Cartridges

1

1

E202

Pneumatic Tool for G5-22 Cartridges

1

1

G5 22 Fluid Ounce Cartridge

Number of Anchoring Installations per Cartridge* Using Reinforcing Bar with G5 Adhesive in Concrete
REBAR
DRILL HOLE DIA. INCHES
EMBEDMENT DEPTH IN INCHES (mm)
1
(25.4)		 2
(50.8)		 3
(76.2)		 4
(101.6)		 5
(127.0)		 6
(152.4)		 7
(177.8)		 8
(203.2)		 9
(228.6)		 10
(254.0)		 11
(279.4)		 12
(304.8)		 13
(330.2)		 14
(355.6)		 15
(381.0)
#3 1/2 388.9 194.5 129.6 97.2 77.8 64.8 55.6 48.6 43.2 38.9 35.4 32.4 29.9 27.8 25.9
#4 5/8 293.8 146.9 97.9 73.5 58.5 49.0 42.0 36.7 32.6 29.4 26.7 24.5 22.6 21.0 19.6
#5 3/4 225.4 112.7 75.1 56.3 45.1 37.6 32.2 28.2 25.0 22.5 20.5 18.8 17.3 16.1 15.0
#6 7/8 182.0 91.0 60.7 45.5 36.4 30.3 26.0 22.7 20.2 18.2 16.5 15.2 14.0 13.0 12.1
#7 1-1/8 87.2 43.6 29.1 21.8 17.4 14.5 12.5 10.9 9.7 8.7 7.9 7.3 6.7 6.2 5.8
#8 1-1/4 77.6 38.8 25.9 19.4 15.5 12.9 11.1 9.7 8.6 7.8 7.1 6.5 6.0 5.5 5.2
#9 1-3/8 81.0 40.5 27.0 20.2 16.2 13.5 11.6 10.1 9.0 8.1 7.4 6.7 6.2 5.8 5.4
#10 1-1/2 66.2 33.1 22.1 16.6 13.2 11.0 9.5 8.3 7.4 6.6 6.0 5.5 5.1 4.7 4.4
#11 1-3/4 40.5 20.2 13.5 10.1 8.1 6.7 5.8 5.1 4.5 4.0 3.7 3.4 3.1 2.9 2.7

* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.

* Oversized holes acceptable but volume of adhesive will increase.

G522 Fluid Ounce Cartridge

Number of Anchoring Installations per Cartridge* Using Threaded Rod with G5 Adhesive in Concrete
ROD In. (mm)
DRILL HOLE DIA. INCHES
EMBEDMENT DEPTH IN INCHES (mm)
1
(25.4)		 2
(50.8)		 3
(76.2)		 4
(101.6)		 5
(127.0)		 6
(152.4)		 7
(177.8)		 8
(203.2)		 9
(228.6)		 10
(254.0)		 11
(279.4)		 12
(304.8)		 13
(330.2)		 14
(355.6)		 15
(381.0)
1/4 (6.4) 5/16 721.2 360.6 240.4 180.3 144.2 120.2 103.0 90.2 80.1 72.1 65.6 60.1 55.5 51.5 48.1
3/8 (9.5) 7/16 417.6 208.8 139.2 104.4 83.5 69.6 59.7 52.2 46.4 41.8 38.0 34.8 32.1 29.8 27.8
1/2 (12.7) 9/16 300.5 150.3 100.2 75.1 60.1 50.1 42.9 37.6 33.4 30.1 27.3 25.0 23.1 21.5 20.0
5/8 (15.9) 3/4 153.8 76.9 51.3 38.4 30.8 25.6 22.0 19.2 17.1 15.4 14.0 12.8 11.8 11.0 10.3
3/4 (19.1) 7/8 121.7 60.8 40.6 30.4 24.3 20.3 17.4 15.2 13.5 12.2 11.1 10.1 9.4 8.7 8.1
7/8 (22.2) 1 100.9 50.5 33.6 25.2 20.2 16.8 14.4 12.6 11.2 10.1 9.2 8.4 7.8 7.2 6.7
1 (25.4) 1-1/8 83.0 41.5 27.7 20.7 16.6 13.8 11.9 10.4 9.2 8.3 7.5 6.9 6.4 5.9 5.5
1-1/4 (31.8) 1-3/8 62.8 31.4 20.9 15.7 12.6 10.5 9.0 7.8 7.0 6.3 5.7 5.2 4.8 4.5 4.2

* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars andthe stress areas of the threaded rods. These estimates do not account for waste.

* Oversized holes acceptable but volume of adhesive will increase.