header

or go to the Advance Search
QuickMenu Save Document

redhead_logo.jpg (5786 bytes)
Hammer-Set ™
Anchors
Hammer-Set Anchor
Approvals and Listing
 
DESCRIPTION / SUGGESTED SPECIFICATIONS

Nail-Drive
Anchors

 

ham_prod1a.jpg (6258 bytes)

 

 

 

 

 Hammer-Set Nail Drive Anchors—
SPECIFIED FOR ANCHORAGE INTO CONCRETE, BLOCK OR BRICK

The Hammer-Set one-piece zinc plated steel anchor consists of an expansion body and expander drive pin. Anchors meet or exceed GSA specification A-A-1925A Type 1. (Formerly GSA: FF-S-325 Group V,
Type 2, Class 3)
 
ADVANTAGES

epcon_a7prod1e.jpg (309 bytes)Fast, easy installation      
epcon_a7prod1e.jpg (309 bytes)Works in concrete, block and brick
epcon_a7prod1e.jpg (309 bytes)Install through material to be fastened
epcon_a7prod1e.jpg (309 bytes)Low profile mushroom head style
APPLICATIONS

*For overhead applications refer to Redi-Drive for information and performance data. 		NOT FOR USE IN OVERHEAD APPLICATIONS*

epcon_a7prod1e.jpg (309 bytes) Electrical boxes
epcon_a7prod1e.jpg (309 bytes)Conduit clips
epcon_a7prod1e.jpg (309 bytes)Drywall track
epcon_a7prod1e.jpg (309 bytes)Roof flashing

APPROVALS/LISTINGS

Meets or exceeds GSA specification A-A-1925A Type 1 (Formerly GSA: FF-S-325 Group V, Type 2, Class 3)

 
INSTALLATION STEPS
1. Drill proper size hole through material to be fastened into base material (See Chart for bit size).
STEP 2 2. Clean hole.
3. Insert Hammer-Set into hole until head of anchor body is flush with material to be fastened. Tap the nail until flush with head of anchor. Ensure minimum embedment is 1/4" deeper than anchor embedment. Be sure head is firmly against fixture.
3. Anchor is now set.

** NOT RECOMMENDED FOR OVERHEARD **
SELECTION CHART
Hammer-Set
  
PART
NUMBER		 DESCRIPTION
In. (mm)		 DRILL
SIZE
In. (mm)		 MAX. FIXTURE
THICKNESS
In. (mm)		 MIN.
EMBEDMENT
In. (mm)		 MIN.
HOLE SIZE
In. (mm)		 QTY/WT
PER BOX
lbs.		 QTY/WT
PER
MASTER
CTN-lbs.
HS-1607 3/16 x 7/8 (4.8 x 22.2) 3/16 (4.8) 1/4 (6.4) 5/8 (15.9) 1-1/8 (28.6) 100/ 2.0 1000/ 20
HS-1406 1/4 x 3/4 (6.4 x 19.1) 1/4 (6.4) 1/8 (3.2) 5/8 (15.9) 1 (25.4) 100/ 2.2 1000/ 22
HS-1410 1/4 x 1 (6.4 x 25.4) 1/4 (6.4) 1/4 (6.4) 3/4 (19.1) 1-1/4 (31.8) 100/ 2.4 1000/ 24
HS-1412 1/4 x 1-1/4 (6.4 x 31.8) 1/4 (6.4) 1/2 (12.7) 3/4 (19.1) 1-1/2 (38.1) 100/ 2.6 1000/ 26
HS-1414 1/4 x 1-1/2 (6.4 x 38.1) 1/4 (6.4) 3/4 (19.1) 3/4 (19.1) 1-3/4 (44.5) 100/ 2.8 1000/ 28
HS-1420 1/4 x 2 (6.4 x 50.8) 1/4 (6.4) 1-1/4 (31.8) 3/4 (19.1) 2-1/4 (57.2) 100/ 3.5 1000/ 35

Bulk Packaging Available

Bulk Hammer-Sets will be shipped in boxes of 1,000 pieces, packaged in 10 individual pages of 100

PERFORMANCE TABLE

Hammer-Set
Ultimate Shear and Tension Values in Concrete (Lbs/kN)*
ANCHOR DIA.
In. (mm)
EMBEDMENT
In. (mm)
4000 PSI (27.6 MPa)
TENSION
Lbs. (kN)
SHEAR
Lbs. (kN)
3/16" (4.8)
5/8" (15.9)
640 (2.8)
810 (3.6)
1/4" (6.4)
3/4" (19.1)
880 (3.9)
970 (4.3)
1/4" (6.4)
1" (25.4)
950 (4.2)
970 (4.3)
1/4" (6.4)
1-1/4" (31.8)
1,025 (4.6)
970 (4.3)

Safe working loads for single installations under static loading conditions should not exceed 25% of the ultimate capacity.

Hammer-Set Nail Drive Anchor
Approvals and Listing

 
ITW Red Head • 2171 Executive Drive • Addison, IL 60101 • 630-350-0370
copyright © 2008 Illinois Tool Works, Inc.